Product Introduce
Novotech's stepper driver represents the highest level in domestic,with 32-bit DSP technology, parameter adjust automatically function, automatic optimization of operating parameters for different motors, to maximize motor performance. Built-in Micro-sub-technology, even in the low micro-step conditions,can achieve high subdivision effect,and the motor run smooth in both low and high speed, with very small noise.
Naming Rules
Classic S Series Drive Models
|
Models |
2204S |
5005S |
5605S |
7208S |
6008SA |
7022SA |
|
Working voltage |
20-40Vdc |
20-50Vdc |
20-50Vdc |
20-80Vdc |
20-80Vac/Vdc |
220Vac |
|
Current setting range |
0.1-2.2A |
1.46-5.0A |
2.1-5.6A |
3.08-7.2A |
3.08-6.0A |
1.7-8.2A |
|
Weight |
0.2Kg |
0.38Kg |
0.41Kg |
0.40Kg |
0.89Kg |
1.1Kg |
Matched stepper
motor model |
35、42 series |
|
|
|
|
|
|
|
57HS0955 |
57HS0955 |
|
|
|
|
|
57HS2280 |
57HS2280 |
|
|
|
|
|
|
86HS3566 |
86HS3566 |
|
|
|
|
|
86HS4576 |
86HS4576 |
|
|
|
|
|
|
|
86HS85118 |
|
|
|
|
|
|
86HS120129 |
86 series |
|
|
|
|
|
86HS120156 |
110、130 series |
|
Pulse limit frequency |
500KHz(Factory default 200KHz) |
|
Protection function |
Overcurrent, overvoltage, undervoltage alarm |
|
Input Signal |
Pulse and direction compatible with the enable signal interface level 4.5-28Vdc,no need external current limiting resistor |
|
Output Signal(can customize) |
Fault signal OC output, the output capacity is 100mA, need an external pull-up resistor, the maximum pull-up voltage is 24Vdc. |
|
Single and double pulse signal |
Factory default receiving single pulse signal, also can receiving dual pulse signal and pulse valid edge by setting host computer. |
|
Subdivision |
according to DIP switch or tuning software to set subdivision（200-51200） |
|
Storage temperature |
-20°C~80°C |
|
Using temperature |
-5°C~55°C |
|
Using Humidity |
40~90%RH |
Main features
● Wide range power supply working voltage, current, and subdivision step adjustment.
● Acceptable differential and single ended pulse/directional commands.
● Pulse, direction, and enable signal interface levels are compatible with 4.5-28Vdc.
● Adopting magnetic flux vector anti resonance algorithm and electronic damping low-speed anti vibration algorithm.
● Automatic identification of motor parameters and automatic adjustment of control parameters during power on.
● Built in microstep subdivision algorithm, achieving low subdivision control instructions and high subdivision operation effect.
Current setting
|
output peak current |
output rms current |
SW1 |
SW2 |
SW3 |
|
Default1.0A[PK] |
on |
on |
on |
|
1.46A |
1.04A |
off |
on |
on |
|
1.91A |
1.36A |
on |
off |
on |
|
2.37A |
1.69A |
off |
off |
on |
|
2.84A |
2.03A |
on |
on |
off |
|
3.31A |
2.36A |
off |
on |
off |
|
3.76A |
2.69A |
on |
off |
off |
|
5.50A |
3.57A |
off |
off |
off |
This is a 5005S current setting table. For other models, please refer to the driver panel for accuracy.
Half And Full Current Set SW4
If the driver does not receive the pulse command after 200ms, it enters the idle mode, SW4 can set the current.
|
Idle current percentage |
SW4 |
|
50% |
OFF |
|
100% |
ON |
Subdivision Setting
|
Pulse/Rev |
SW5 |
SW6 |
SW7 |
SW8 |
|
Default |
on |
on |
on |
on |
|
400 |
off |
on |
on |
on |
|
800 |
on |
off |
on |
on |
|
1600 |
off |
off |
on |
on |
|
3200 |
on |
on |
off |
on |
|
6400 |
off |
on |
off |
on |
|
12800 |
on |
off |
off |
on |
|
25600 |
off |
off |
off |
on |
|
1000 |
on |
on |
on |
off |
|
2000 |
off |
on |
on |
off |
|
4000 |
on |
off |
on |
off |
|
5000 |
off |
off |
on |
off |
|
8000 |
on |
on |
off |
off |
|
10000 |
off |
on |
off |
off |
|
20000 |
on |
off |
off |
off |
|
25000 |
off |
off |
off |
off |
This is a 5005S subdivision setting table. For other models, please refer to the driver panel for accuracy.
2204S Dimensional Drawing
5005S、5605S、7208S Dimensional Drawing
6008SA Dimensional Drawing
7022SA Dimensional Drawing
Wiring diagram
VIDEO
CONTACT
